K&N – 2009-10 Dodge Ram 5.7L Hemi Gets More Oomph!

KN_77-1561KP-KNN

KN_77-1561KP-KNN

Buy Online @ JDMUltimate.com

K&N released an air intake with a  polished aluminum tube for the 2009-2010 Dodge Ram 1500 V8 5.7L. This intake, part 77-1561KP, has shown a 10.3 horsepower increase @ 4382 RPM when tested on K&N’s dynamometer.  This easy performance add-on comes with K&N’s million mile limited warranty.

The appearance of the polished aluminum tube, which is adapted with a 90 degree elbow, will dress up your engine so it is ready for show. This intake includes a heat shield that surrounds the high flow cone shaped air filter for protection against engine heat.

K&N air intakes provide outstanding engine protection and can go up to 50,000 miles before the oversized air filter needs to be serviced. With this simple addition you will get a show truck look with power you can feel. K&N air intakes can typically be installed in 90 minutes or less. Complete installation instructions are available on KNFilters.com.

Buy Online @ JdmUltimate

Advertisements

K&N – 2009 Acura TSX K24 2.4L Gets More Air!

KN_69-0026TS-2009 Acura TSX K24 2.4L

KN_69-0026TS-2009 Acura TSX K24 2.4L

Buy Online @ JDMUltimate.com

The 2009 Acura TSX is a well-built entry-level luxury car that comes standard with leather seats, dual-zone climate control and a USB port music interface. This second-generation TSX is larger than its predecessor and offers more interior space to its passengers. The modernized exterior styling of the 2009 Acura TSX makes it an attractive vehicle. Great handling, performance and recognized reliability are only a few of the reasons consumers continue to rave about the Acura TSX.

K&N designed an air intake system (69-0026TS) for 2009 Acura TSX models with a 2.4 liter engine. The 69-0026TS was engineered specifically to fit the cramped quarters of the TSX engine compartment. By completely replacing the restrictive factory air filter and intake housing of the 2009 Acura TSX with K&N’s custom intake tube and high-flow performance air filter (RC-4630XD), K&N achieved a dramatic increase in horsepower.

Power testing was performed on this air intake system to determine how much horsepower could be obtained with this simple intake modification. The 69-0026TS showed an increase of 7.86 horsepower at 5400 rpm when tested on a 2009 Acura TSX with a 2.4L in-line 4-cylinder engine.

The 69-0026TS intake reduces air restriction, compared to the factory intake, with its large K&N high-flow air filter and its powder coated silver aluminum tube.  K&N’s design adds performance while providing outstanding filtration for the life of your Acura TSX.  The air filter can go up to 100,000 miles before servicing is required depending on driving conditions.  The entire air intake system comes with K&N’s million mile limited warranty.

K&N provides detailed installation instructions that help make installing your 69-0026TS cold air intake system simple. Typical installation takes 90 minutes or less and only uses common hand tools.

Buy Online @ JdmUltimate

K&N – Cold Air Intake For The Nissan Cube! Part # 69-7077TTK

K&N-69-7077TTK

K&N-69-7077TTK

Buy Online @ JDMUltimate.com

The Nissan Cube was a step in a new direction for compact four-door station wagons. This block-shaped hatchback brings a unique style to the wagon segment that has never been seen before. The Nissan Cube is offered in several trim levels and provides plenty of headroom and legroom for all occupants.

The Nissan Cube is a fun and comfortable ride but can use more power on the road. K&N saw this need for more horsepower and designed the 69-7077TTK cold air intake system. The 69-7077TTK was designed for the 2009 and 2010 Nissan Cube equipped with the 1.8 liter engine. K&N guarantees your Nissan Cube will increase horsepower with this simple performance modification.

The 69-7077TTK completely replaces the factory air filter and intake housing with a textured black aluminum induction tube and K&N high-flow performance air filter (RC-9350). The 69-7077TTK is designed to last the life of your Nissan Cube and backed by K&N’s million mile limited warranty.

In-house dyno testing shows the 69-7077TTK delivering 7.78 horsepower at 4886 rpm. 2009 and 2010 Nissan Cube owners can easily boost their horsepower with K&N’s cold air intake system. Installation of this system is usually done in 90 minutes or less.

Buy Online @ JdmUltimate

K&N – 2009 Honda Fit Owners get an Extra 5HP

Buy Online @ JDMUltimate.com

The 2009 Honda Fit was completely redesigned for 2009. It is a bit longer and wider than the 2008 model and has added interior space, sharper handling, enhanced seating functionality, and a more powerful engine.

K&N has designed a performance air intake system (69-1017TTK) in black for the 2009 Honda Fit with a 1.5 liter engine that is guaranteed to increase power.  K&N dynamometer tests show the 1.8 liter engine gained 4.53 horsepower at 6000 RPMs with this air intake kit.

The 69-1017TTK has lower restriction than the factory air box system. It draws air through a high flow washable and reusable chrome top K&N air filter (RC-9630) which is protected by a powder coated heat shield.

The heat shield directs incoming fresh air from the factory air inlet into the air filter and isolates the K&N air filter from the engine compartment for better performance. The heat shield assembly is installed into the engine bay using factory mounting points and attaches to the intake tube.

The 69-1017TTK integrates the mount from the vehicle’s mass air sensor. Remove the mass air sensor from your vehicle’s stock air box and install it into K&N’s less restrictive mandrel bent aluminum tube using the provided K&N hardware.

All the OE emissions devices are reused and the MAS placed in a location that works with the factory settings. The provided crankcase vent hose attaches to the aluminum intake tube. The 69-1017TTK can be easily installed in 90 minutes or less and is backed by the famous K&N Million Mile Limited Warranty.

Buy Online @ JdmUltimate

K&N – Viper Owners Get a Bit More Venom

K&N-VIPER-INTAKE

K&N-VIPER-INTAKE

Buy Online @ JDMUltimate.com

The 2008 Dodge Viper defines brute power. Equipped with an 8.4-liter, 10-cylinder engine, the 2008 Dodge Viper is capable of producing over 600 horsepower. The Viper is often considered primitive when compared to ultra-luxurious supercars from Europe. However, what the Viper lacks in plush trim and options, it makes up for with its track credentials.

The 2008 Viper is reported to accelerate from 0-60 mph in 3.7 seconds, cover the quarter mile in 11.8 seconds, and reach top speeds of around 200 mph. Combine that level of sheer power with the ability to precisely maneuver through turns, stop from 60-0 mph in around 100 feet, and the 2008 Viper will leave a venomous taste in mouths of European supercar owners.

K&N engineers are always hunting for more power. After looking under the 2008 Viper’s hood, K&N engineers knew the Viper was capable of more. Much consideration was put into the design of part number 69-2527TTR.
The stock 2008 Viper intake tract uses a dual throttle body set up fed by a common plenum with a single air filter. K&N intake 69-2527TTR replaces the stock pieces with twin powder coated mandrel-bent aluminum intake tubes and dual K&N high-flow air filters for improved air delivery.

KN-69-2527TTR-Installed-K&N-VIPER-INTAKE

KN-69-2527TTR-Installed-K&N-VIPER-INTAKE

This performance air intake system incorporates a unique heat shield, and the dual air filters line up with the factory fresh air intake on the hood. The result of this hard work and enthusiasm for performance is a nearly 19 horsepower gain at the wheels.

K&N’s Research and Development Department tested a 2008 Dodge Viper 8.4-liter V10 on our in-house dynamometer. Results showed horsepower increases throughout the RPM range with a shocking peak horsepower gain of 18.69 horsepower @ 5,300 RPM! 69-2527TTR provides improved performance with attractive red powder coated aluminum intake tubes to match the 2008 Viper’s valve covers.

K&N air intakes completely replace the restrictive factory air intake assembly with an aerodynamically engineered tube and an oversized air filter. With a K&N Performance Air Intake System, consumers can count on extra horsepower whether cruising along with fellow Viper owners, or competing at Laguna Seca.

This air intake system uses two conical shaped, chrome topped, high-flow air filters (RF-1048) and a powder coated aluminum heat shield in place of the vehicle’s stock air box. The result is an air filter that captures harmful particles, flows more air, and provides long service life. This K&N air filter performs for up to 100,000 miles before service is required, depending on driving conditions. Improving the air path between the filter and the engine are the powder coated aluminum intake tubes. Our powder coated aluminum intake tubes offer power and a stylish appearance. 69-2527TTR takes about 90 minutes or less to install, using stock mounting points, requires no drilling, and is covered by the K&N Million Mile Limited Warranty.

For increased protection and style, includes K&N intake 69-2527TTR Drycharger® filter wraps (RF-1048DK) intended be used during inclement weather. Drychargers are made from a durable polyester material containing uniform micron openings which will stop small dirt particles and repel water; yet add little restriction to the airflow of the filter. Available in a variety of colors, K&N Drychargers can be color coordinated with a car’s finish.

Buy Online @ JdmUltimate